:: Search Products ::

CVO250 - Control Valve Orifice Fitting , 1/4" MNPT x 3/8" MGF

CVO250

CVO250 - Control Valve Orifice, 1/4" MNPT, #61 Orifice

The CVO250 gas flow needle valve control valve orifice allows you to fine control the level of the pipe burner flames at the venturi rather than back at the propane tank regulator or the natural gas source. If you purchase a Control Valve Orifice at the time you purchase any pipe burner we will drill it to the proper orifice size and install it on your pipe burner at no extra charge. The default orifice size is #61. This control valve orifice fitting will work on practically any burner if the orifice is drilled to the proper size.

Specify your fuel preference of: natural gas, low pressure propane, or high pressure propane in the Comments section in the shopping cart.

Wt. 2.5 oz. Free shipping to the 48 contiguous U.S. States.

CVO250 needle valve control on a straight pipe burner
CVO250 Install in a Pipe Burner Venturi

$39.95

CVO250 - Control Valve Orifice Fitting , 1/4" MNPT x 3/8" MGF

CVO250

CVO250 - Control Valve Orifice 1/4" MNPT, #61 Orifice

The CVO250 needle valve control valve orifice allows you to fine control the level of the pipe burner flames right at the venturi rather than back at the propane tank regulator or the natural gas source. If you purchase a Control Valve Orifice at the time you purchase any pipe burner we will drill it to the proper orifice size and install it on your pipe burner at no extra charge.The default orifice size is #61. This control valve orifice fitting will work on practically any burner if the orifice is drilled to the proper size.

Specify your fuel preference of natural gas, low pressure propane, or high pressure propane in the Comments section in the shopping cart. Free shipping to the 48 contiguous U.S. States.

CVO250 Needle Control Valve on a Square Pipe Burner

$39.95

CVO - Control Valve Orifice Fitting , MNPT x 3/8" MGF

CVO

CVO - Gas Flow Control Valve Orifice Fitting, for any gas burner.
1/8" or 1/4" MNPT x 3/8" MGF

►   This needle valve will replace the existing Male NPT orifice fitting. Permits control over the flame height right at the burner.

►   High pressure cast burners use a #61 orifice. Low pressure and natural gas burners require a larger orifice size. If you are not
sure, send us a picture of the burner. We will help you choose.

►   Custom size orifices are drilled at no extra charge.

Wts.1.9 oz, 2.2 oz, 2.7 oz. Free shipping to the 48 contiguous U.S. States.

CVO125 Control Valve Orifice Fitting
CVO250 Control Valve Orifice Fitting

$39.95

Gas Flow Control Valve Orifice Fitting for any Gas Burner

PBM125 - Straight Pipe Burner -Support Leg Option, Ideal for Hog Roasters, Pig Cookers

PBM125

PBM125 - Straight Pipe Burner 1.25" ID in 32", 44", 56", or 68" lengths. Support LEGS available as an option. Used in Hog Roasters, Pig Cookers, Gun Bluing, Maple Syrup Evaporation, and BBQ Pits.

♦ 32", 44", 56", and 68" standard pipe burners lengths.

♦ Constructed with a permanently welded plate steel disk at one end and our 1.25" NPT threaded HPMAX-1 venturi at the opposite end.

♦ Pipes measure 1.25"ID/1.5"OD with a 3/16" wall thickness.

♦ Eight inches of pipe near the venturi is used as the "throat" of the burner and does not have any holes for flames.

♦ A 32" burner has 24" of flames, 44" burner has 36" of flames, 56" burner has 48" of flames, and a 68" burner has 60" of flames.

Indicate your fuel preference of natural gas, low pressure propane, or high pressure propane in the COMMENTS section of the shopping cart. Propane is expensive so don't waste propane using a pipe burner which gives an inefficient yellow flame.

You can provide support of the assembly by using a cradle made of a length of 1.5" angle iron. Such a cradle support permits easy removal for maintenance. These pipe burners are designed to give even, high-heat blue flames throughout the length of the pipe. They are easy to light.

♦ With Low Pressure use we suggest the COM5 regulator/hose.
♦ With High Pressure use we suggest the COM3 regulator/hose.
♦ Available with an Optional Needle Control Valve with integral Orifice.
♦ CustomPipeBurners.com can weld permanent 1/2" diameter round supporting legs along the length of any pipe burner. Order the unit with "LEGS" at the end of the part number, (shown in drop-down order box to the right).
♦ Custom length stainless steel pipe burners of any length can be manufactured to order. Call for a quote.

Free shipping to all 48 contiguous U.S. States.

Weight Weight w/LEGS
PBM125-32" 10# 14#
PBM125-44" 12# 18#
PBM125-56" 15# 22#
PBM125-68" 18# 26#

Free shipping to the 48 contiguous U.S. States.

Straight Pipe Burner with Optional CVO250 Control Valve Orifice
Straight Pipe Burner with Optional Legs and CVO250
Straight Pipe Burner with Optional Legs and CVO250
Pilot Light Assembly is available as an Option at additional charge

$299.95

PBMG125 - Straight Pipe Burner and Integral Grease Shield - Optional Leg Supports - For Hog Roasters, Pig Cookers

PBMG125

PBMG125 - Straight Gas Pipe Burner, 1.25" ID in 32", 44", 56", or 68" lengths, with a permanently welded 3" high grease shield. Optional LEGS

In every pipe burner there will be 8" of pipe without gas holes for air and gas mixing after the venturi:

  ♦  32" pipe burner has 24" of flames
  ♦  44" pipe burner has 36" of flames
  ♦  56" pipe burner has 48" of flames
  ♦  68" pipe burner has 60" of flames

A standard stocked pipe burner can be reduced in length to fit a custom length required by a customer. Length reductions are made to that part of the pipe burner with the flame holes. See the area below for how to request a custom length pipe burner. Specify your fuel preference of natural gas, low pressure propane, or high pressure propane in the Comments section in the shopping cart.

♦ For Low Pressure use we suggest a COM5 regulator/hose.
♦ For High Pressure use we suggest a COM3 regulator/hose.
♦ Available with an Optional Needle Control Valve with integral Orifice
♦ CustomPipeBurners.com can weld permanent 1/2" diameter round legs along the length of your pipe burner. Order the unit with "LEGS" at the end of the part number, as shown in the drop down box to the right.

Free shipping to all the 48 contiguous U.S. States.

  Wt.w/Grease Shield  Wt.w/Grease Shield & LEGS
PBMG125-32" 12# 13#
PBMG125-44" 16# 18#
PBMG125-56" 20# 22#
PBMG125-68" 24# 26#

Free shipping to the 48 contiguous U.S. States.

(12) Straight Pipe Burners with Grease Shields in One Gas Manifold
Dual Pipe Burners with Grease Shields
Straight Pipe Burner with Grease Shield and Optional CVO250
Straight Pipe Burner with Grease Shield and Optional Support Legs

$349.95

Straight Pipe Burner with a Grease Shield, ideal for use in Hog Roasters or Pig Cookers

SQPB - Square Pipe Burner - (support LEGS are an option)

SQPB

SQPB - Square Pipe Burner with 10", 15", or 20" equal sides. Optional LEGS

If you would like CustomPipeBurners.com to weld permanent 1/2" diameter round support legs along the perimeter of your square pipe burner then order the unit with "LEGS" at the end of the part number, as shown in the drop down box to the right. Specify your fuel preference of natural gas, low pressure propane, or high pressure propane in the Comments section in the shopping cart.

Square Pipe Burners can be run by High Pressure Propane,
Low Pressure Propane or Natural Gas.

For High Pressure use we recommend the COM3 regulator/hose.
For Low Pressure use we recommend the COM5 regulator/hose.
Also available with an Optional Needle Control Valve with Orifice.

Free shipping to the 48 contiguous U.S. States.

Weight: Weight w/LEGS:
10" x 10" 10# 13#
15" x 15" 13# 16#
20" x 20" 17# 20#

Square Pipe Burner with Optional CVO250
Custom Pipe Burner with 1 1/4" Unions
Square Pipe Burner with Optional Support Legs and CVO250

$399.95

A125AM - 1 1/4" Cast Aluminum Venturi Gas and Air Mixer

A125AM

OUT OF STOCK

PLEASE NOTE:

We will have more in stock by
JANUARY 2025

You can still order them right now as Pre-Order,
but keep in mind they will be shipping out until
JANUARY 2025.

A125AM - 1 1/4" Cast Aluminum MONSTER Venturi Gs and Air Mixer.

- Aluminum Casting Made in Houston, Texas. Made-in-U.S.A.

- No Paint Needed, No Rust and Light Weight.

- It has a 1 1/4" Female Normal Pipe Thread Outlet.
- To be used with High Pressure / Low Pressure Propane or
Natural Gas.

- The flat top surface is 4" in Diameter by 2 1/2" in height.
- The height of the venturi with an orifice is approximately 4".

- Includes an Aluminum Air Shutter, Insect Screen Guard and a
90 3/8" Flare Orifice, with #61 Orifice for High Pressure Propane.

- Alternatively, a 180 3/8" Flare Orifice fitting is also available.
- Drilled to custom orifice size depending on your specified fuel and
length of pipe burner or specified burner at No Extra Charge.

(For alternative orifice or custom drilled orifice please let us know the
information in comment box section when added to shopping cart).

For High Pressure use we recommend the COM3 regulator/hose.

For Low Pressure use we recommend the COM5 regulator/hose.

The Optional CVO Needle Control Valve with Orifice.

Also available with a C-Pilot Assembly.

Weight 1#. Free Shipping within the 48 contiguous U.S. States.

1 1/4 Female Threads

Female NPT Oulet Threads 1 1/4"

The photos below show the different Options which can be choosen from the drop-down menu above the price.

OPTIONS:

Cast Aluminum Venturi, Air and Gas Mixer

Cast Aluminum Venturi, Air and Gas Mixer

A125AM with 90 Degree Orifice, $ 149.95

A125AM with CVO Neddle Control Valve Orifice, $ 179.95

Cast Aluminum Venturi, Air and Gas Mixer with Pilot Assembly

A125AM with C-PILOT Assembly, $ 229.95

$149.95

A125AM - 1 1/4" Cast Aluminum Venturi Gas and Air Mixer

SQPBG - Square Pipe Burner with Grease Shield - (support LEGS are an option)

SQPBG

SQPBG - Square Pipe Burner with a permanently welded Grease Shield: 10", 15", or 20" equal sides. Optional LEGS

If you would like CustomPipeBurners.com to permanently weld 1/2" diameter round support legs along the perimeter of your square pipe burner then order the unit with "LEGS" at the end of the part number, as shown in the drop down box to the right. Specify your fuel preference of natural gas, low pressure propane, or high pressure propane in the Comments section in the shopping cart.

Square Pipe Burners can be run by High Pressure Propane,
Low Pressure Propane or Natural Gas.

For High Pressure use we recommend the COM3 regulator/hose.
For Low Pressure use we recommend the COM5 regulator/hose.
Also available with an Optional Needle Control Valve with Orifice.

Free shipping to the 48 contiguous U.S. States.

Wt. w/Grease Shield: Wt. w/Grease Shield & LEGS:
10" x 10" 15# 17#
15" x 15" 22# 24#
20" x 20" 28# 30#

Square Pipe Burner with Grease Shield and Optional CVO250
Square Pipe Burner with Grease Shield and Optional Support Legs
VIDEO

$549.95

Square Pipe Burner with a permanent Grease Shield

SQB6 - 6" x 6" Two Part Square Burner

SQB6 - 6

SQB6 - 6" x 6" Two Part Square Burner

- Made in Houston, Texas. Made-in-U.S.A.

- 40,000 Btu's

- Can be set up for Low Pressure Propane or Natural Gas

- Two Part Burner, Pipe Nipple NOT Included

- 3/4" Female NPT

- Reference Video

OPTIONS:

SQB6 with 90 Degree Orifice, $ 259.95

SQB6 with CVO Neddle Control Valve Orifice, $ 299.95

SQB6 with C-PILOT Assembly, $ 339.95

$259.95